Get prices for a new immersion element in Gosport
An immersion switched on with a cold cylinder may need only a new thermostat. Note whether the immersion goes in from the top or the side.
One short description of the problem in Gosport can reach up to four independent heating engineers, depending on who works in your postcode. The matching is free. You can turn down every quote.
What the engineer will check
This job replaces a failed immersion element or thermostat in a hot water cylinder. The power is isolated, the cylinder drained below the immersion boss, the new element fitted, and the cylinder refilled before the heater is tested.
What you might be seeing
- A cold cylinder with the immersion on
- The RCD going off as the immersion starts
- Water only lukewarm after hours of heating
- Loud noises from the cylinder while heating
- One switch working and the other not on a dual element
What the engineer does
The engineer should test before replacing. The visit usually covers:
- Switching off the power and proving it dead, then turning off the cold feed.
- Testing the element and thermostat to find which has failed.
- Emptying the cylinder below the immersion boss.
- Removing the old element and fitting the new one with a fresh washer.
- Topping up the cylinder, checking for leaks, then testing the heater with power on.
Unvented cylinders need the specified replacement
An unvented cylinder needs the element, thermostat and safety cut-out specified for that model. Ask the engineer to check the manufacturer’s instructions and confirm their competence with unvented systems before ordering a replacement.
Access and finishing up
Clear the airing cupboard so the engineer can reach the element without stretching over stored items. Agree what happens if the old element will not release, and ask for leak checks and electrical testing before handover.
The cost of immersion heater replacement in Gosport
Our indicative allowance is £150–£400. Engineers here price their own work. A thermostat swap with no draining sits at the bottom of the range. An element and thermostat in a vented copper cylinder is in the middle. An unvented element or a seized element that needs careful removal sits at the top.
Ask for the call-out fee, parts and labour to be shown separately, with VAT stated. Allow 2–4 hours for the work itself; awkward access or waiting for a part can take longer.
Before you send the form
Say whether the cylinder is vented, with a loft tank, or unvented, with a pressure gauge and expansion vessel. Note whether the immersion is on the top or the side and whether there are one or two switches. Describe what happens when you switch it on.
Then pin down what the price covers. Ask whether draining, the element and thermostat, refilling and electrical testing are included. Check what the engineer will do if the old element is seized or the boss is damaged.
Rules that apply to the work
In England, replacing an immersion like for like on an existing circuit is not usually notifiable under Part P, but a new circuit is. Rules elsewhere in the UK differ. Use someone competent in electrical work and, for an unvented cylinder, its safety controls. The immersion heater advice from Electrical Safety First covers why the thermostat and safety cut-out matter. Never run an element before the cylinder is full.
Building control questions for this area can go to Hampshire County Council. If the job expands beyond a straightforward repair, confirm which approvals apply before the extra work starts.
Booking immersion heater replacement near you
Give the full postcode for the property in Gosport, Hampshire. Note any communal entrance or parking permit. Send a clear photo of the cylinder label and immersion position. Neighbouring houses often have different systems, so describe the one in yours.
Other places around Gosport
Work in another part of Hampshire needs its own enquiry and postcode. Availability can differ between neighbouring postcodes.
Portsmouth, Newport, Fareham, Ryde, Bembridge, Yarmouth, WaterloovilleCompare what local engineers include
The free enquiry form takes a couple of minutes. We ask engineers who join for their insurance details and references, but check insurance and recent experience of similar jobs before you hire anyone. We pass on your enquiry. The business you choose gives the advice, sets the price and carries out the work.
If you smell gas, leave the property and call the National Gas Emergency Service on 0800 111 999 (Great Britain). This service does not arrange emergency call-outs. In Northern Ireland, the gas emergency number is 0800 002 001; for LPG, contact your supplier.
Before booking this work
How can I compare quotes for immersion heater replacement in Gosport?
Fill in one enquiry form with your postcode and details of the cylinder type and whether the heater stays cold or trips. It can go to as many as four independent heating engineers who work in Gosport. How many reply varies with the job and how busy engineers are, and booking any of them is up to you.
Roughly how much is immersion heater replacement in Gosport?
We use £150–£400 as a UK guide. Engineers in Gosport price their own work, and the system, access and parts affect the total. A written quote should list labour, parts, VAT and any call-out fee.
Can an immersion heater be replaced without draining the cylinder?
A thermostat can usually be changed without draining. A new element needs the water level below the immersion boss, which means draining some or all of the cylinder.
Are titanium immersion elements worth it?
In hard water areas they often last longer than standard copper, because they resist scale and corrosion better. They cost more to buy, so ask the engineer whether your water makes the difference worthwhile.
Is it safe to keep using an immersion that trips the breaker?
No. A tripping immersion has a fault that needs testing. Turn it off at the switch if you can reach it safely, and book a visit instead of resetting the breaker each time.
How long should I allow for immersion heater replacement?
Allow 2–4 hours as a guide. Once the engineer has seen the system, they should tell you how long the heating or hot water will be off. Waiting for a part or awkward access can add time.